More Shops Are Swapping Conventional Wheels For Vitrified CBN

Nov 20, 2026

Leave a message

In steel grinding, replacing conventional aluminium oxide and silicon carbide wheels with vitrified bond CBN is no longer a new proposition. The shift has left a fairly complete record of numbers stretching back to the 1980s, and that record goes some way to explaining why tooling, bearing and automotive plants worked through the change one after another.

  • Why replace traditional grinding wheels with superhard material grinding wheels?
  • CBN Grinding Wheel
  • Diamond Grinding Wheel

 

 

1. Two rising curves, ten years apart

Published industry data puts the vitrified-bond share of total CBN abrasive output worldwide at 4% in 1980 and 37% by 1993. For the Chinese market, the vitrified CBN wheel share is recorded moving from 4% in 1990 to 32% by 2000.

Scope Period From To
Worldwide, vitrified bond as a share of total CBN abrasives 1980–1993 4% 37%
China, vitrified CBN wheel market share 1990–2000 4% 32%

Both series start at the same 4% and both finish above thirty percent, but the windows sit about a decade apart. That gap maps roughly onto the period in which China moved from first trials to volume adoption.

Vitrified Bond CBN Diamond Grinding Wheel 1A1
1A1 Vitrified Bond CBN Diamond Grinding Wheel

2. How other markets progressed over the same years

Japan reached widespread use comparatively early. Public accounts date the start of vitrified CBN use there to 1973, with output rising several-fold between 1985 and 1990 and the technology entering general adoption around 1990. At the 16th Japan Machine Tool Fair, 18 of the 34 grinding machines on show carried vitrified CBN wheels - a majority of the exhibits.

Russia at the time produced roughly 60 million carats of CBN a year, most of it going into vitrified bond products.

In 1993, world consumption of CBN abrasives was put at about USD 265 million, against a potential market estimated in excess of USD 1.2 billion. The distance between consumption and potential indicates that substitution was still under way at that point.

3. Why vitrified bond in particular

The bond itself is durable and forgiving. Vitrified bond resists heat, oil, water and acids, holds form well and keeps dimensional accuracy stable. Its open structure leaves room for chip clearance and coolant, which limits loading and burning. It self-sharpens readily, dresses at longer intervals than metal bond, and dresses more easily - at moderate cost. These characteristics line up with the demands of CNC grinders and transfer lines.

CBN is inert to iron-group metals. Diamond reacts with iron-group elements at elevated temperature; CBN does not, which makes it suitable for steel parts as well as a range of non-metallic materials, giving it a broader working range than diamond. Its thermal stability in hot, oxygen-bearing conditions is also better than diamond's.

The efficiency gains are measured, not asserted. Published accounts describe grinding automotive camshafts at HRC45 with a φ600 mm vitrified CBN wheel at 65 m/s, with production efficiency up by about 10%. Results on harder-to-machine parts such as injector needle valve bodies are similarly pronounced. In shipbuilding, the same class of wheel has been applied to hardened gear flanks.

Dressing is where the maintenance saving sits. Longer dressing intervals mean fewer stoppages, lower dresser consumption and less labour. That saving does not appear in the wheel price, but it does appear in cost per part.

4. China started early, if not first

Vitrified bond CBN abrasives were taken up in China from the late 1970s - broadly the same window as Japan's adoption phase. The φ600 mm, 65 m/s camshaft case cited above, and the use of these wheels on hardened gear flanks in shipbuilding, were both domestic applications. In other words, local manufacturing did not begin from a standing start; the groundwork was laid last century.

5. How the cost case should be framed

A vitrified CBN wheel costs more per piece than a conventional wheel; there is no argument about that. The case for switching rests on cost per part, not on purchase price:

  • Grinding ratio - more material removed per unit of wheel consumed, so wheel consumption per unit of work falls;
  • Dressing - longer intervals cut dressing cycles and dresser consumption together;
  • Throughput - the roughly 10% gain recorded on camshaft work translates directly into cycle time and capacity;
  • Labour and downtime - fewer wheel changes and dressing stops mean less idle machine time.

Added together, the price difference is usually absorbed. The reverse also holds: grinding steel with conventional wheels means lower efficiency, more frequent wheel changes and dressing that consumes labour, which pushes cost per part up. That is why substitution happened first in the sectors named above.

6. Where the substitution stops

Vitrified CBN does not outperform conventional wheels on every operation. Selection in practice usually follows these lines:

Application Suitable abrasive Reason
High-volume steel grinding, hard-state work Vitrified CBN Form retention, long dressing intervals, stable cycles on CNC and transfer lines
Rough grinding, low-precision work, small batches Conventional aluminium oxide or silicon carbide Cost advantage where surface finish and cycle stability are not critical
Cemented carbide, ceramics, glass, stone Diamond Non-ferrous hard and brittle materials fall outside CBN's working range

Concentration and grit size also have to match the workpiece and stock allowance. A higher concentration does not automatically improve results; where the operation does not call for it, it only adds cost.

7. How a conversion is usually run

The sequence set out in published guidance is unglamorous, and can be reduced to four steps:

  1. Assess high-volume steel grinding operations first, rather than running the whole plant on conventional wheels by default;
  2. run comparative trials on benchmark parts - camshafts or bearing rings - recording grinding ratio, wheel life and cycle time;
  3. settle the dressing process at the same time; vitrified bond is dressed differently from metal bond and needs its own parameters;
  4. judge on total cost rather than unit price, then fix concentration and grit size accordingly.

Closing

From 4% to above thirty percent took a decade on the Chinese figures; in Japan, from first use in 1973 to general adoption around 1990 took seventeen years. What happened in both cases was a recalculation of the cost structure of a grinding operation - not simply an upgrade of the abrasive.

About huicetools: a professional manufacturer of diamond tools, founded in 2006. With years of hands-on experience, we sell factory-direct at highly competitive prices. Our product line covers Diamond Segment,  diamond saw blades, diamond grinding blocks, diamond drill bits and a full range of diamond tools for construction & Stone applications.

Disclaimer: This article is adapted and rewritten from publicly available reports on the Chinese Internet and open industry sources, and is provided for industry reference only. Market shares, output figures, market size and efficiency data cited herein are historical statistics recorded in public sources; the measurement basis and reference years rest with the original documents and do not describe present market conditions. Statements on application range reflect common industry practice, and actual selection should take account of workpiece material, stock allowance and machine conditions. We make no representation as to their completeness, accuracy or timeliness, and this article does not constitute investment or procurement advice. For republication or citation, please contact huicetools and credit the original source.

Send Inquiry