Common quality problems of diamond segment

Feb 12, 2023

Leave a message

In the production process of diamond segment, there will be various problems, including improper operation in the production process, as well as various reasons in the formulation and binder mixing process. Many of these problems have affected the use of the diamond segment. Generally, the diamond segment can not be used or can not work well, affecting the production efficiency of slate and even increasing production costs. The quality problems of diamond segment are as follows:

 

1 There is a problem with the size and specification of the diamond segment

 

Although the diamond segment is the mixture of metal alloy and diamond sintered by a fixed mold, and the final product is finished by cold pressing and hot pressing sintering, and the material is relatively fixed, due to the insufficient sintering pressure, the insufficient sintering temperature, or the insufficient temperature and pressure of heat preservation and pressure preservation during the sintering process, which will lead to uneven stress on the diamond segment, so the reason for the difference in the size and specification of the diamond segment will naturally occur, The most obvious manifestation is the height of the diamond segment.

 

The pressure will be high if the pressure is not enough, and the pressure will be low if the pressure is too high. Therefore, it is very necessary to stabilize the same pressure and temperature in the production process. Of course, in the early loading process, the diamond segment cold pressing material should also be weighed; Also pay attention not to take the wrong mold, which will lead to the scrapping of the diamond segment. The size of diamond segment does not meet the requirements, the density is not enough, the hardness does not meet the requirements, there are sundries in the transition layer, and the strength of the diamond segment is not enough.

20230212133925

 

2 The density is not enough, and the diamond segment is soft

 

In the process of cutting stone, the dense and soft diamond segment will break. The fracture can be divided into local fracture and overall fracture. No matter which kind of fracture, such diamond segment can no longer be used. Of course, the breakage of the diamond segment is the limit. When cutting stone, the diamond segment with insufficient compactness will also fail to cut or the diamond segment will consume too fast due to its insufficient Mohs hardness. In general, the compactness of the diamond segment must be guaranteed.

 

This situation is generally caused by sintering temperature, holding time, insufficient pressure, wrong selection of binding material, high diamond content of diamond segment, etc. This situation is very common. This situation also occurs in the old formula. The main reason is the improper operation of workers. If it is a new formula, most of the reasons are due to the designers' insufficient grasp of the formula, Designers need to better mix the diamond segment formula and give more reasonable sintering temperature and pressure in combination with temperature and pressure.

diamond segment hot press
diamond segment hot press
3 The diamond segment cannot cut the stone

 

The main reason why the diamond segment can't cut stone is that the strength is not enough, and there are five main reasons for insufficient strength:

1: Insufficient diamond or poor quality of selected diamond;


2: Impurities, such as graphite particles, dust, etc., are mixed into the diamond segment during mixing and loading, especially in the mixing process, uneven mixing will also lead to this situation;


3: The diamond is excessively carbonized, and the temperature is too high, resulting in serious diamond carbonization. During the cutting process, the diamond particles are easy to fall off;


4: The diamond segment formula design is unreasonable, or the sintering process is unreasonable, resulting in the low strength of the working layer and the transition layer (or the working layer and the non-working layer are not tightly combined), which usually occurs in the new formula;


5: The diamond segment bond is too soft or too hard, resulting in the disproportionate consumption of diamond and metal bond, and thus the diamond matrix bond cannot hold the diamond powder.

diamond segment

 

 

4 Diamond segment falls off

 

There are many reasons for the diamond segment to fall off, such as too many impurities, too high or too low temperature, too short heat preservation and pressure retention time, inappropriate formula ratio, unreasonable welding layer, different formula of working layer and non-working layer, resulting in different thermal expansion coefficients of the two.

 

When the diamond segment cools down, shrinkage stress occurs at the connection between the working layer and non-working layer, resulting in the diamond segment strength reduction, and finally the diamond segment to fall off. These reasons are the reasons that lead to the falling of the diamond segment or the segment of the saw blade. To solve this problem, first of all, it is necessary to ensure that the powder is fully mixed and free of impurities, and then match reasonable pressure, temperature, and heat preservation time, and try to ensure that the thermal expansion coefficient of the working layer and non-working layer is close.

 

During the processing of the diamond segment there will be other problems, such as excessive consumption, such as jamming, such as eccentric wear, etc. Many problems are not only caused by the diamond segment, but may be caused by mechanical, stone type and other factors. We will introduce them in detail in the following article.

 

 

Send Inquiry